不同微喷弥雾调控方式下微气候因子对极端干旱区葡萄果实生长及糖度的影响

通过对极端干旱区葡萄在不同微喷弥雾调控方式（WP1,架上喷水1 h;WP2，架下喷水1 h；WP3，地上喷水1 h）下微气候因子与葡萄果实生长形态及糖度的监测，分析葡萄园微气候因子变化规律及其与葡萄果实生长形态和糖度的关系。结果显示：采用微喷弥雾调控可有效降低葡萄园温度和增加湿度，与CK处理（常规滴灌，不喷水）相比，白天平均温度低2.9℃~3.3℃，平均温度低2.5℃~2.9℃，夜晚平均湿度高4.7%~5.5%，同时可促进葡萄果实生长和糖度累积，WP1、WP2和WP3与CK处理相比，果粒纵茎高出2.88、1.76、0.9 mm，果粒横茎高出1.33、1.80、1.76 mm，果粒均重高出0.22、0.26、0.25 g，糖度分别高出7.75%、3.96%和5.53%。在葡萄果实生长发育过程中，白天平均温度和平均温度是影响葡萄纵径和横径的关键微气候因子，晚上平均湿度是影响葡萄果实重量和糖度的关键微气候因子，在白天平均温度为30.4℃~33.8℃、晚上平均湿度为49.5%~50.5%时接近葡萄果实纵径、横径和果粒均重拟合值最大值。根据其相互关系和建立的回归模型，得出可以用白天平均温度、平均温度和晚上平均湿度对该地区葡萄生长和糖度变化进行分析和预测。     

北方粳高粱微波干燥特性试验与仿真分析*

为明确微波干燥条件对高粱含水率和籽粒温度等干燥特性的影响,以粳高粱“龙杂10”为原料,在隧道式微波干燥机上进行连续式干燥试验。并利用HFSS软件仿真分析试验用干燥机的磁控管排布方式和微波作用距离对高粱干燥均匀性的影响。结果表明:随着单位质量功率在2~6 W/g范围内逐渐增加,含水率下降幅度先加快后渐缓,籽粒温度有所下降;每循环干燥时间在1.02~5.0 min范围内逐渐增加,含水率下降幅度显著增强,籽粒温度增加显著;排湿风速在0.0~2.0 m/s范围增加,含水率下降幅度有减小趋势,籽粒温度略有下降。仿真分析表明干燥机磁控管采用“三二三排布方式”、微波作用距离为250 mm时电磁场分布的均匀性更好,从理论上表明本试验采用的隧道式微波干燥机对高粱干燥均匀性是有利的。研究结果将为高粱微波干燥产业化应用提供理论和数据支持。     

Modelling optimal timing and frequency of insecticide sprays for knockdown in preparation for other control measures

A modelling investigation was conducted into optimizing the number of sprays and inter-spray interval to reduce an insect population to a low level, for example, prior to pheromone trapping or the release of sterile males. The model population was age-structured and density-dependent. If spray mortality is 100% for each spray, then the ideal spraying schedule is easily determined from the durations of the various life stages. For spray mortality of less than 100%, a simulation was used to determine optimal spraying schedules. Relative length of the larval period, fertility rate and age to first oviposition were found to be the most important biotic parameters for this determination. Their importance is magnified as spray mortality decreases. The stage targeted by sprays and the percent mortality caused by each spray are also important in determining the required number of sprays. Using medfly (Ceratitis capitata Wiedmann) biotic parameters as an example when the spray targets adults, it appeared that neither the stage at which density-dependent mortality takes effect, nor the form of the adult survivorship curve are important in determining the optimal spray schedule.     

绿茶低温负压干燥工艺优化研究

干燥是绿茶品质定型的关键工序之一，为生产优质绿茶，尤其是保留色泽和营养成分，对绿茶的干燥工艺进行了探索。通过比较传统热风干燥和低温负压干燥，发现低温负压的干燥效率平均提高30%，且在内质成分保留方面具有明显优势。分别以干燥时间、叶绿素、水浸出物、氨基酸，儿茶素和茶多酚含量为考察指标，采用多指标正交试验优化绿茶低温负压干燥工艺，结果表明，绿茶最优低温负压干燥条件为干燥温度75 ℃，负压（0.03 MPa）4 min，低温15 min。应用最优工艺加工超微茶粉，与传统工艺超微茶粉比较发现，低温负压干燥技术可有效保留原茶主要品质成分，提高超微茶粉品质。     

自动折叠喷洒臂的设计及运动学特性

为了解决当前卷盘式喷灌机所配套的喷灌车自动化水平较低的问题,设计了一种基于电动缸驱动的自动折叠喷洒臂,并在喷洒臂之间连接处设计了一种当喷洒臂完全展开时能够实现自密封的端面密封铰链.基于喷洒臂完全折叠时收拢于车架两侧,完全伸展时铰链左右铰合密封等特征建立各杆件参数约束方程,确定了喷洒臂的各杆件尺寸.通过矢量方程法对喷洒臂进行运动学分析,以电动杆推杆的转角、位移、速度、加速度为输入量,各杆件的角位移、角速度、角加速度为输出量,通过Simulink搭建喷洒臂的运动仿真框图并进行分析.结果表明:完全折叠时,喷管1与水平方向呈90°夹角;伸展过程中,各喷管运动平稳,且始终保持在水平直线方向;完全展开时,3个喷管转动90°,且各喷管铰接处完全闭合不发生水泄漏现象,说明设计具有一定的合理性.     

喷雾降温风机风筒优化设计与试验

为缓解高温热害对茶果树的影响,基于圆弧板型叶片模型设计了一种喷雾降温风机,并对风筒结构进行建模和动力学仿真。以出风口直径、进风段长度和出风段长度为试验因素,以风机出口总压和风速为试验指标,采用Design-Expert 8.0.6软件优化风筒结构参数。优化结果表明,各因素对出口总压和风速的影响由大到小依次为出风口直径、出风段长度、进风段长度。最优参数组合为出风口直径1 070 mm、进风段长度350 mm和出风段长度270 mm。选取WJ-7010、WJ-8010型喷嘴,利用优化后的风筒结构进行了风速试验和喷雾降温性能试验。风速试验表明,当风筒出风口直径和总长度分别为1 070、840 mm时,出风口风量为701.30 m~3/min,最大风速为16.00 m/s,有效送风距离约为55.00 m。喷雾降温性能试验结果表明,当使用WJ-8010型喷嘴时,与对照组相比,平均温度降低0.68～11.11℃,最大温差范围为1.80～13.90℃。在38℃高温环境下,喷雾降温风机在20 m范围内的降温幅度接近5℃,降温效果良好。     

5种农药低空喷雾防治黄脊竹蝗成虫效果分析

为确定低空喷雾无公害药剂防治黄脊竹蝗成虫的林间最佳浓度水平和用药量，掌握低空喷雾施药技术，在福建省三明市三元区的毛竹林建立试验区，应用无人机开展低空喷雾防治试验。结果表明：药后7 d，5种农药的防治效果均超过90%，其林间最佳浓度水平（药剂与纯净水的体积比）为：1.5%苦参碱可溶液和1.2%烟碱·苦参碱乳油均为1：1 000；25%阿维·灭幼脲悬浮剂为1：700，1%苦参·藜芦碱可溶液和4%鱼藤酮乳油均为1：600，原药量用为900 mL/hm²。5种农药防治效果良好，可推广应用于防治黄脊竹蝗成虫。     

400克/升氯氟醚菌唑悬浮剂对香蕉叶斑病的防治效果

通过大田试验研究了400克/升氯氟醚菌唑悬浮剂防治香蕉叶斑病效果及其对香蕉产量的影响。研究结果表明,分别以20毫升、13.3毫升、10毫升400克/升氯氟醚菌唑悬浮剂兑水60公斤分3次喷雾施药,第二次施药后14d后对香蕉叶斑病防治效果在60.43-66.52%,第三次施药后14d后对香蕉叶斑病防治效果在75.72-80.72%,并对香蕉的单株产量有明显增产效果。其中尤以20毫升400克/升氯氟醚菌唑悬浮剂兑水60公斤剂量喷雾处理的效果最好。     

Growth,yield and water productivity of dry direct seeded rice and transplanted aromatic rice under different irrigation management regimes

Sustainability of traditionally cultivated rice in the rice-wheat cropping zone (RWCZ) of Pakistan is dwindling due to the high cost of production, declining water resources and escalating labour availability. Thus, farmers and researchers are compelled to find promising alternatives to traditional transplanted rice (TPR). A field study was conducted in Punjab, Pakistan, in 2017 and 2018 to explore the trade-offs between water saving and paddy yield, water productivity and economics of two aromatic rice varieties under dry direct seeded rice (DDSR) and TPR. The experiment was comprised of three irrigation regimes on the basis of soil moisture tension (SMT) viz., continuous flooded (>−10 kPa SMT), alternate wetting and drying (AWD) (−20 kPa SMT) and aerobic rice (−40 kPa SMT), maintained under TPR and DDSR systems. Two aromatic rice verities: Basmati-515 and Chenab Basmati-2016 were used during both years of study. In both years, DDSR produced higher yields (13–18%) and reduced the total water inputs (8–12%) in comparison to TPR. In comparison to traditional continuous flooded (CF), AWD under DDSR reduced total water input by 27–29% and improved the leaf area index (LAI), tillering, yield (7–9%), and water productivity (44–50%). The performance of AWD with regard to water savings and increased productivity was much higher in DDSR system as compared to AWD in TPR system. Cultivation of DDSR with aerobic irrigation improved water savings (49–55%) and water productivity (22–30%) at the expense of paddy yield reduction (36–39%) and spikelet sterility. With regard to variety, the highest paddy yield (6.6 and 6.7 t ha⁻¹) was recorded in DDSR using Chenab Basmati-2016 under AWD irrigation threshold that attributed to high tiller density and LAI. The economic analysis showed DDSR as more beneficial rice establishment method than TPR with a high benefit-cost ratio (BCR) when the crop was irrigated with AWD irrigation threshold. Our results highlighted that with the use of short duration varieties, DDSR cultivation in conjunction with AWD irrigation can be more beneficial for higher productivity and crop yield.     

大型海藻干燥技术研究进展

干燥是海藻储存、加工、生产的重要方法之一,不同的干燥方式对海藻脱水效率、能耗和品质影响很大。本文对藻类传统干燥和新型干燥技术的特点、研究及应用现状进行了分析。研究表明,太阳能干燥技术能够充分做到干燥过程中绿色、环保,与空气热泵构成组合干燥模式,可解决太阳能不连续的问题;过热蒸汽干燥效率高、能耗低,藻类干燥后复水性好;真空冷冻干燥产品品质好,能最大限度保持藻类的营养和功能性成分;远红外加热技术对海带进行干燥,与同风速的热风干燥相比,可显著缩短干燥时间,降低能耗;微波真空干燥技术干燥江蓠,在保持品质的基础上干燥时间较热风干燥减少70%。本文同时对藻类干燥技术与设备存在的问题进行了总结,对国内藻类干燥技术及装备的发展趋势进行了展望并提出了措施与建议。